| MIDDLE VOLTAGE POWER
CABLES |
|
Type Designation
|
Rated
Voltage |
Conductors |
Construction |
| Number |
Sectional (mm2)
|
 |
| Designation - N2XS2Y |
6/10 kV
12/20 kV
18/30 kV
|
1
1
1 |
35 to 500
35 to 500
50 to 500
|
- The cables with XLPE insulation are with high quality and are safe
and reliable during exploation.
- The XLPE insulation is with high electric strength and low dielectric
losses.
- The three-layer insulating system of conductive layer of the core
- XLPE insulation - conductive layer and the technological process
of simultaneous triple extrusion provide low level of partial discharges
at 2Uo < 2 pC.
- The XLPE insulation is with good thermal and physical characteristics
and withstands mechanical loads during laying and installation.
- The sheath of PE does not comply with the requirements of flame
retardancy for single cable method B according to VDE 0472 part 804.
|
Standard - IEC 60502-2,
DIN VDE 0276-620 |
| Type - Single-core
with Cu wires, XLPE insulation, Cu screen and PVC sheath |
 |
| Application and Remarks:
The single-core cables with insulation of cross-linked polyethylene (XLPE)
are designed for transfer and distribution of electrical power with nominal
voltage Uo/U 6/10, 12/20 and 18/30 kV and frequency 50 Hz in urban and
district electrical networks and for electrical supply of transformers
substations, small and medium industrial plants.They are suitable for
use in distribution installations, electric power stations and industrial
systems.The cables are for fixed assembly and indoor installation, in
cable ducts and conduits, over shelves and grilles in water and directly
underground in ditch and outdoor under shelter. |
|
| Designation - N2XS(F)2Y |
6/10 kV
12/20 kV
18/30 kV
|
1
1
1 |
35 to 500
35 to 500
50 to 500
|
- The cables with XLPE insulation are with high quality and are safe
and reliable during exploation.
- The XLPE insulation is with high electric strength and low dielectric
losses.
- The three-layer insulating system of conductive layer of the core
- XLPE insulation - conductive layer and the technological process
of simultaneous triple extrusion provide low level of partial discharges
at 2Uo < 5pC.
- The XLPE insulation is with good thermal and physical characteristics
and withstands mechanical loads during laying and installation.
- The PE sheath does not comply with the requirements of flame retardancy
for single cable method B according to VDE 0472 part 804.
|
Standard - IEC 60502-2,
DIN VDE 0276-620 |
| Type - Single-core
with Cu wires, XLPE insulation, Cu screen and PVC sheath |
 |
| Application and Remarks:
The single-core cables with insulation of cross-linked polyethylene (XLPE)
are designed for transfer and distribution of electrical power with nominal
voltage Uo/U 6/10, 12/20 and 18/30 kV and frequency 50 Hz in urban and
district electrical networks and for electrical supply of transformers
substations, small and medium industrial plants. They are suitable for
use in distribution installations, electric power stations and industrial
systems. The cables are for fixed assembly and indoor installation, in
cable ducts and conduits, over shelves and grilles in water and directly
underground in ditch and outdoor under shelter. |
|
| Designation - N2XSEY, 2XSEY |
3.6/6kV
6/10kV
12/20kV
18/30kV
|
3
3
3
3 |
35 to 300
35 to 300
35 to 300
35 to 300
|
- The cables with XLPE insulation are with high quality and are reliable
during exploitation.
- The XLPE insulation is with high electric strenght and low dielectric
losses.
- The three-layer insulation system of conductive layer of the core
- XLPE insulation - conductive layer and the technological process
of simultaneous triple extrusion provide low level of partial discharges
at 2Uo<2pC.
- The XLPE insulation is with good thermal and phisical characteristics
and withstands mechanical loads during laying and installation.
|
Standard - IEC 60502-2
DIN VDE 0276-620 |
| Type - Three-core
with Cu wires XLPE insulation, Cu screen and PVC sheath |
 |
| Application and Remarks:
The three-core cables with insulation of cross-linked poliethylene (XLPE)
are designed for transfer and distribution of electrical power with nominal
valtage Uo/U 3.6/6; 6/10; 12/20 and 18/30 kV and frequency 50 Hz in urban
and district electrical networks and for electrical supply of transformers
substations, small and medium industrial plants.They are suitable for
use in distribution installations, electric power stations and industrial
systems.The cables are for fixed assembly and indoor installation, in
cable ducts and conduits, over shelves and grilles in water and directly
underground in ditch and outdoor under shelter. |
|
| Designation - N2XSY |
6/10 kV
12/20 kV
18/30 kV
|
1
1
1 |
35 to 500
35 to 500
50 to 500
|
- The cables with XLPE insulation are with high quality and are safe
and reliable during exploation.
- The XLPE insulation is with high electric strength and low dielectric
losses.
- The three-layer insulating system of conductive layer of the core
- XLPE insulation - conductive layer and the technological process
of simultaneous triple extrusion provide low level of partial discharges
at 2Uo < 2 pC.
- The XLPE insulation is with good thermal and physical characteristics
and withstands mechanical loads during laying and installation.
|
Standard - IEC 60502-2
DIN VDE 0276-620 |
| Type - Single-core
with Cu wires, XLPE insulation, Cu screen and PVC sheath |
 |
| Application and Remarks:
The single-core cables with insulation of cross-linked polyethylene (XLPE)
are designed for transfer and distribution of electrical power with nominal
voltage Uo/U 6/10, 12/20 and 18/30 kV and frequency 50 Hz in urban and
district electrical networks and for electrical supply of transformers
substations, small and medium industrial plants.They are suitable for
use in distribution installations, electric power stations and industrial
systems.The cables are for fixed assembly and indoor installation, in
cable ducts and conduits, over shelves and grilles in water and directly
underground in ditch and outdoor under shelter. |
|
| Designation - NA2XS2Y |
6/10 kV
12/20 kV
18/30 kV
|
1
1
1 |
35 to 500
35 to 500
50 to 500
|
- The cables with XLPE insulation are with high quality and are safe
and reliable during exploation.
- The XLPE insulation is with high electric strength and low dielectric
losses.
- The three-layer insulating system of conductive layer of the core
- XLPE insulation - conductive layer and the technological process
of simultaneous triple extrusion provide low level of partial discharges
at 2Uo < 2 pC.
- The XLPE insulation is with good thermal and physical characteristics
and withstands mechanical loads during laying and installation.
- The sheath of PE does not comply with the requirements of flame
retardancy for single cable method B according to VDE 0472 part 804.
|
Standard - IEC 60502-2
DIN VDE 0276-620 |
| Type - Single-core
with Al wires, XLPE insulation, Cu screen and PVC sheath |
 |
| Application and Remarks:
The single-core cables with insulation of cross-linked polyethylene (XLPE)
are designed for transfer and distribution of electrical power with nominal
voltage Uo/U 6/10, 12/20 and 18/30 kV and frequency 50 Hz in urban and
district electrical networks and for electrical supply of transformers
substations, small and medium industrial plants.They are suitable for
use in distribution installations, electric power stations and industrial
systems.The cables are for fixed assembly and indoor installation, in
cable ducts and conduits, over shelves and grilles in water and directly
underground in ditch and outdoor under shelter. |
|
| Designation - NA2XS(F)2Y |
6/10 kV
12/20 kV
18/30 kV
|
1
1
1 |
35 to 500
35 to 500
50 to 500
|
- The cables with XLPE insulation are with high quality and are safe
and reliable during exploation.
- The XLPE insulation is with high electric strength and low dielectric
losses.
- The three-layer insulating system of conductive layer of the core
- XLPE insulation - conductive layer and the technological process
of simultaneous triple extrusion provide low level of partial discharges
at 2Uo < 5pC.
- The XLPE insulation is with good thermal and physical characteristics
and withstands mechanical loads during laying and installation.
- The PE sheath does not comply with the requirements of flame retardancy
for single cable method B according to VDE 0472 part 804.
|
Standard - IEC 60502-2
DIN VDE 0276-620 |
| Type - Single-core
with Al wires, XLPE insulation, Cu screen and PVC sheath |
 |
| Application and Remarks:
The single-core cables with insulation of cross-linked polyethylene (XLPE)
are designed for transfer and distribution of electrical power with nominal
voltage Uo/U 6/10, 12/20 and 18/30 kV and frequency 50 Hz in urban and
district electrical networks and for electrical supply of transformers
substations, small and medium industrial plants.They are suitable for
use in distribution installations, electric power stations and industrial
systems.The cables are for fixed assembly and indoor installation, in
cable ducts and conduits, over shelves and grilles in water and directly
underground in ditch and outdoor under shelter. |
|
| Designation - NA2XSEY,A2XSEY |
3.6/6kV
6/10kV
12/20kV
18/30kV
|
3
3
3
3 |
35 to 300
35 to 300
50 to 300
|
- The cables with XLPE insulation are with high quality and are reliable
during exploitation.
- The XLPE insulation is with high electric strenght and low dielectric
losses.
- The three-layer insulation system of conductive layer of the core
- XLPE insulation - conductive layer and the technological process
of simultaneous triple extrusion provide low level of partial discharges
at 2Uo<2pC.
- The XLPE insulation is with good thermal and phisical characteristics
and withstands mechanical loads during laying and installation.
|
Standard - IEC 60502-2
DIN VDE 0276-620 |
| Type - Three-core
with Al wires XLPE insulation, Cu screen and PVC sheath |
 |
| Application and Remarks:
The three-core cables with insulation of cross-linked poliethylene (XLPE)
are designed for transfer and distribution of electrical power with nominal
valtage Uo/U 3.6/6; 6/10; 12/20 and 18/30 kV and frequency 50 Hz in urban
and district electrical networks and for electrical supply of transformers
substations, small and medium industrial plants.They are suitable for
use in distribution installations, electric power stations and industrial
systems.The cables are for fixed assembly and indoor installation, in
cable ducts and conduits, over shelves and grilles in water and directly
underground in ditch and outdoor under shelter. |
|
| Designation - NA2XSY |
6/10kV
12/20kV
18/30kV
|
1
1
1 |
35 to 500
35 to 500
50 to 500
|
- The cables with XLPE insulation are with high quality and are safe
and reliable during exploation.
- The XLPE insulation is with high electric strength and low dielectric
losses.
- The three-layer insulating system of conductive layer of the core
- XLPE insulation - conductive layer and the technological process
of simultaneous triple extrusion provide low level of partial discharges
at 2Uo < 2 pC.
- The XLPE insulation is with good thermal and physical characteristics
and withstands mechanical loads during laying and installation.
|
Standard - IEC 60502-2
DIN VDE 0276-620 |
| Type - Single-core
with Al wires, XLPE insulation, Cu screen and PVC sheath |
 |
| Application and Remarks:
The single-core cables with insulation of cross-linked polyethylene (XLPE)
are designed for transfer and distribution of electrical power with nominal
voltage Uo/U 6/10, 12/20 and 18/30 kV and frequency 50 Hz in urban and
district electrical networks and for electrical supply of transformers
substations, small and medium industrial plants.They are suitable for
use in distribution installations, electric power stations and industrial
systems.The cables are for fixed assembly and indoor installation, in
cable ducts and conduits, over shelves and grilles in water and directly
underground in ditch and outdoor under shelter. |
Photo Gallery